Fourth of July Wooden Sign with Cricut ExploreFourth of July Wooden Sign with Cricut Explore

Hey there! I am so excited to be guest posting here at the Crafting Nook today. My name is Brandi and I blog at the Creative Cutting Classroom. I help Cricut Explore users learn how to use their Cricut machines with simple, step-by-step tutorials that move users from being intimidated to confident. Today I brought this super easy and cute Painted Fourth of July Wooden Sign made with Cricut Explore.

Fourth of July Wooden Sign with Cricut Explore

Fourth of July Wooden Sign with Cricut Explore by Creative Cutting Classroom at The Crafty Nook

The Cricut Explore is an amazing addition to your crafting and DIY projects. If you have been thinking of getting one but aren’t sure what model to choose, check out this guide.

Today we will be making a DIY painted wood sign using the Cricut Explore and Cricut stencil vinyl.

Fourth of July Wooden Sign with Cricut Explore

Materials:

  • half inch birch plywood 7.75 inches by 11 inches
  • Cricut stencil vinyl
  • red and white acrylic paint
  • transfer tape
  • fine grit sandpaper
  • paint brush or sponge

Tools:

  • Cricut Explore
  • Cricut cutting mat
  • Cricut weeding tool
  • Cricut scraper tool

1. Sand & Paint Wood

Begin by sanding your wood so that the surface is smooth. This makes it easier for the stencil to stick and not have any paint bleed underneath it. Paint the wood with white acrylic paint using a sponge or brush. Set aside to let dry.

If needed, gently sand again and apply a second coat of white paint. It is important to let it dry long enough, even overnight if you are able. If you don’t, the stencil will peel parts of the white paint up with it when it is removed.

2. Cut the Stencil

I designed the stencil in Cricut Design Space using a USA shape and the Four Seasons Home Decor font. You can access the cut file by clicking here.  The project should open in Design Space and will be ready to cut.

I cut my stencil vinyl at 8 inches tall before I put it on my mat so I didn’t have to trim it down after I cut my design.

Apply the stencil vinyl to the cutting mat and go over it with the scraper tool to make sure it is flat and stuck down well. On the Cricut machine turn the dial to custom settings. On the cutting screen in Design Space there is a drop down menu to select the custom material. We want the setting that says “Stencil Vinyl (Cricut)”

Once you have your mat ready and your settings chosen, load the mat and push the cut button. When it is finished unload the mat.

A step-by-step tutorial on how to make a painted wooden sign for 4th of July using the Cricut Explore and Cricut stencil vinyl.

3. Prepare Stencil

Using the weeder tool, peel away the parts of the stencil where the paint will go. Make sure you remove all of the insides of the letters as well.

Next, apply the transfer tape on the top of the stencil and smooth it out with the scraper tool. The tape I had on hand was narrow, but most transfer tape will cover the entire piece at once. If you use the Cricut brand transfer tape, press it against your shirt or put your hands on the sticky side before using it. If you don’t the Cricut brand is super sticky!

A step-by-step tutorial on how to make a painted wooden sign for 4th of July using the Cricut Explore and Cricut stencil vinyl.

4. Apply Stencil

Turn the stencil over and pull the backing off. Turn it back over and place it on the wood. Use the scraper tool to make sure it is adhered well and it is completely smooth with no bubbles.

Gently pull the transfer tape off of the stencil. Instead of pulling straight up on it,  peel up a corner and lay it flat against the sign and pull, similar to the photo above where I removed the backing. Once the tape is removed, rub it with the scraper again and make sure it is adhered well, especially around the letters.

5. Seal with ModPodge

The worst thing about making a sign is when the paint bleeds under the stencil. You’ve done all of that work only to have lines that aren’t crisp! To make sure this doesn’t happen, put a thin layer of modpodge over the stencil where you are going to paint. Make sure you get it completely covered, but not too thick. This will seal the edges so that no paint bleeds through.

A step-by-step tutorial on how to make a painted wooden sign for 4th of July using the Cricut Explore and Cricut stencil vinyl.

6. Paint with Acrylic Paint

Once the modpodge has dried for five or ten minutes, begin painting with the red acrylic paint. Paint a thin layer and let it dry and then paint another.

7. Peel Stencil and Touch Up

I peel the stencil up while the paint is still slightly wet, partly because it has always worked for me and partly because I’m just impatient! Be very careful to not allow the stencil to touch anything as you are peeling it up.

Use the weeder tool to peel up the letters. If anything did bleed, the paint should still be wet enough to scrape some of it off and use a tiny brush to make touch ups.

A step-by-step tutorial on how to make a painted wooden sign for 4th of July using the Cricut Explore and Cricut stencil vinyl.

8. Tada! Show Everyone You Know How Awesome You Are

Once your sign is finished take it across the room and put it on your shelf or mantel. Now back up and look at it. Those little imperfections you keep focusing on? Let them go. Nothing you ever make handmade will be perfect. The more you make, the better you will be, but no sign will ever be perfect-and that is ok.

I would love to see the signs you make! Come join our facebook group and share your work…it is so fun to see all the different things everyone makes!

I have created a checklist for you to have when you are making your signs that walks you through step-by-step. Just click the button below to be grab your copy!

If you like this project you might also like these too:

Hope you enjoyed this tutorial! See you soon!

Brandi!

And you can also check these as well:

Cute DIY Farmer's Market Tote {using the Cricut Explore}

Baby Girl Owl Onesie Baby Shower Gift #babyshowerideas #owlonesie #onesiedecoration #silhouetteprojects
Cute Heat Transfer Vinyl Pompom Bunny Tail Onesie


4 Comments on Fourth of July Wooden Sign with Cricut Explore

  1. avatar
    Laurie says:
    July 9, 2017

    All of your projects are awesome, but I especially like the God Bless America sign. I have not had much luck using Cricut cuts as stencils, so I appreciate the tutorial. Thanks for sharing at Bitten by the Bug 2.

  2. avatar
    Maureen says:
    July 8, 2017

    Great patriotic project. Thanks for the instructions, I have not tried the pre mod podge technique and excited to try it. Thanks for joining our BBTB2 challenge this week!

  3. avatar
    Janis Lewis says:
    July 6, 2017

    Fabulous projects! Thanks for sharing at Bitten by the Bug 2.
    ~DT Janis

  4. avatar
    Caroline says:
    July 6, 2017

    This is such a wonderful patriotic sign and makes a nice decor piece. Thank you for including the instructions on how to make it. Thanks for joining us at BBTB2.

Leave me your lovely thoughts